Crashes after upgrading to 3.5

[hansjohnson]

I recently upgraded to 3.5.2.2 via Steam and have installed Runtime 6.0.1.3 x64 & x86.

After Lunching ZusiSim.64.exe it enters the default screen like the screenshot below, but nothing is clickable. It automatically exits after a few seconds without reporting an error.

[Carsten Hölscher]

What is the 32 bit version doing?

Carsten

[hansjohnson]

What is the 32 bit version doing?

Carsten

Same as 64.

[F. Schn.]

Does it report an error in the Windows Error Log?

[hansjohnson]

Does it report an error in the Windows Error Log?

No error report.

[Bernhard K.]

Not sure if it makes sense, but what you could try is running Zusi through x64dbg (File -> Open, then press Debug -> Run a few times until the Program exits) and check the "Log" tab for error messages.

[Carsten Hölscher]

Do the other Zusi programs start?

Carsten

[hansjohnson]

Do the other Zusi programs start?

Carsten

Zusi3DEditor.64 (3.5.2.1) OK
ZusiDateiverwaltung.64 (3.5.2.1) OK
ZusiFtdEditor.64 (3.5.2.1) OK
ZusiFzgEditor.64 (3.5.2.1) OK

ZusiDisplay.64 (3.5.3.0) OK

[F. Schn.]

Looks like a problem with the web view component. But I'm not sure how to verify this...
Are there some unexpected folders in the ZusiSim.64.exe directory?

[hansjohnson]

Looks like a problem with the web view component. But I'm not sure how to verify this...
Are there some unexpected folders in the ZusiSim.64.exe directory?

I think no.

[Carsten Hölscher]

In the 3D-Editor a preview of the "Befehl" uses the webview, too.

Carsten

[F. Schn.]

In the 3D-Editor a preview of the "Befehl" uses the webview, too.

To reproduce:
* Open Routes\_Docu\Kap3_Uebungsstrecke\000442_005680_Eslohe\Eslohe_1980.st3
* Press Ctrl+F -> 212 -> OK
* Press Ctrl+E
* Press "Signaleigenschaften / signal settings" at the blue direction
* Select Tab "Ersatzsignale/Substitute signals"
* Select the first column
* Press "Befehls-ID ermitteln... / Compute order ID..."
* Press "Test+Schließen / Test + Close"

There should appear a Browser Engine Window "Deutsche Bundesbahn Befehl B" and the 3D-Editor should not crash.

[hansjohnson]

The problem still exists, opens then freezes.

[Flo Zille]

Can you try the steps given by F.Schn. in Zusi3DEditor.64.exe to see if they work or crash the 3D Editor?

[hansjohnson]

In the 3D-Editor a preview of the "Befehl" uses the webview, too.

To reproduce:
* Open Routes\_Docu\Kap3_Uebungsstrecke\000442_005680_Eslohe\Eslohe_1980.st3
* Press Ctrl+F -> 212 -> OK
* Press Ctrl+E
* Press "Signaleigenschaften / signal settings" at the blue direction
* Select Tab "Ersatzsignale/Substitute signals"
* Select the first column
* Press "Befehls-ID ermitteln... / Compute order ID..."
* Press "Test+Schließen / Test + Close"

There should appear a Browser Engine Window "Deutsche Bundesbahn Befehl B" and the 3D-Editor should not crash.

After I pressed Test+Schließen, it closes, and nothing appears, no browser engine window, no error message.

[F. Schn.]

it closes

Does the Window "Befehls-ID ermitteln... / Compute order ID..." close and the 3D-Editor main window remains open, or does the 3D-Editor close in total?

[hansjohnson]

it closes

Does the Window "Befehls-ID ermitteln... / Compute order ID..." close and the 3D-Editor main window remains open, or does the 3D-Editor close in total?

Everything closed.

[hansjohnson]

Thank you guys, although I don't know why, but it is OK now

[F. Schn.]

Strange... But at least it's sloved.

- F. Schn.